![]() I feel like my camera is far enough away from the road and it seems like the camera doesn’t pick up stuff some days better than others but without zones or being able to adjust sensitivity levels I don’t have many options here. Let me know if you need me to provide anything else. I would expect more recordings to be available for that amount of space assuming some level of compression and my clips are only 10 seconds long, but that’s what I’m encountering.Īll events above that don’t have a description next to them are either cars driving by or lights shining in the distance which perhaps are causing the PIR sensor to freak out but I know next to nothing about PIR sensors. I have a 32GB card and I did not tell it to wipe/format since initially installing the card. No additional recordings are available after that 16:24 (4:24PM ET) event yesterday. 20:37 me returning and leaving my house again.So far today (five events, all cars in the distance i.e. All times are in military time in the Eastern timezone. Looking back at my alert history I actually get less than one alert per hour on some days, but then other days it’s a much higher amount.įor example, below is the alert history since I left my house last night for a walk. Documentation hints at sensitivity settings under the Smart Detection settings area but for me all I get is the the Alert Frequency setting (which has always been set to Low).įirst things first, here is a picture to explain the setup better than a thousand words could possibly do: I was really hoping the Kami with its larger rechargeable capacity batteries would be the final solution but for me I feel there’s still work left for the software guys. I had the same issue with my Blink camera at the same location until they worked out the same issue, but of course their product takes two double A batteries and I hated the waste of burning through batteries (and had no power hookup available for a constant power solution). Having the ability to adjust the sensitivity would greatly improve this product instead of having to readjust the camera. ![]() From where it’s located to the road it’s probably 25 feet in distance, give or take a few feet. I’d say I get about one per hour, one 10 second clip. The camera will go into retrieving pairing status that can take 1-2 minutes.Thanks for the reply Mark - I didn’t get an email notification of the reply so I had no idea you responded, but thank you. If you did not hear anything, click on the link at the bottom of the screen.Ĩ. If you hear “QR code scan is successful,” press next. Then face the QR code directly at the camera. Under Connect to Wi-Fi enter the password for the Wi-Fi router. If you don’t hear waiting to connect click on the link called, I did not hear it.Ħ. Then select, I hear “Waiting to connect” at the bottom of the screen. Scan the QR code on the bottom of the camera.ĥ. If you aren’t sure, click on the QR code under Select Device(s). Under Select Device(s), choose the camera that is going to be paired with the app. To add your camera, select the '+' icon.Ĥ. Open the App and log in to your account.ģ. The camera can also be powered by only the USB cable if it's plugged into a device that provides power through USB.Ģ. Connect the camera with the USB cable and adapter, and plug the adapter into a power outlet. Here are the steps to pair your camera to the app:ġ. Android: Settings > Security & Location > Privacy > Location should be ON. IOS: Settings > Privacy > Location Service > Make sure that the YI Home App is set to WHILE USING.ī. Ensure the Location or GPS on your phone is enabled, and Allow the permissions for your App.Ī. Once you move your camera near the Wi-Fi router, there should be no obstructions or any objects that may block the signal from the router to your camera.Ĥ. While connecting/adding your camera, it's suggested to place the camera near your Wi-Fi router. Make sure that you've entered your correct Wi-Fi password.ģ. Please check your Wi-Fi settings before pairing up and make sure that you are connected to a 2.4GHz Wi-Fi network.Ģ. Check a few things to avoid issues with pairing:ġ.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |